INCRA table saw fence review
A good and manageable table saw is every woodworker’s dream. While precise management of a table saw seemed almost impossible before, it is now possible with the INCRA table saw fence.
INCRA has been doing an amazing job ever since they started. They are constantly bringing new products in the market upgrading the ones they already have to fit in and adapt to the demands of their clients.
In this article, we have tried to mention all the good and bad sides of the INCRA table saw fence, and how it works. So read the whole article find out if you want this in your life or not.
- 1 INCRA Table Saw Fence
- 2 Incra table saw fence compatibility
- 3 INCRA table saw fence specifications:
- 4 Incra table saw fence installation
- 5 Key features and upgrades
- 5.1 INCRA METRIC with an upgrade for large table
- 5.2 INCRA METRIC with wonder fence
- 5.3 INCRA METRIC wonder fence and an upgrade for large table
- 5.4 INCRA METRIC with wonder fence and 234 cm rails
- 5.5 TS-III Support Legs
- 5.6 Metric INCRA LS 32 – Positioner Only
- 5.7 Incra Base Assembly METRIC – only for Table Saw Fence
- 5.8 Metric Wonder Fence Upgrade – WF/ULTRA
- 5.9 INCRA Large-Saw Conversion Upgrade
- 5.10 TS Base Mount Package with 72″ rails and 32″ Rip Capacity
- 5.11 TS Base Mount Package with 92″ rails and 52″ Rip Capacity
- 5.12 Pair rail mounting brackets with mounting hardware
- 5.13 INCRA Router Table and Support Hardware Kit TSRTHW
- 5.14 Pros:
- 5.15 Cons:
INCRA Table Saw Fence
The INCRA table saw a fence that comes with an amazing structural design. The carriage is positioned in the middle. The side mounted clamping system ensures great stability and strength.
Incra table saw fence compatibility
Incra table saw fence systems are available in two sizes – 32″ and 52″, 810 mm, and 1320 mm range models. The system shows very low friction so you get just the perfect alignment relative to the blade. You can initially align the fence in parallel to the miter slot.
You get two rail lengths:
The 32″ (810mm) – This system uses a rail length of 72″.
The 52″ (1320mm) – This system uses a 92″ rail length.
Both of these systems use the same quick-release knobs and LS32 Positioner. It helps the positioner’s base assembly to shift further from the saw blade on the longer blade of the 52″ system so it can achieve greater capacity. This system comes with TS Rail Support Legs which are of great help.
With the help of the quick-release feature of the knobs, one can adjust the positioner’s base assembly and position any place along the length of the rails. You can remove the base assembly in just a few seconds, giving you total access to the saw’s surface.
This also lets the base assembly to be reversed on the rails. This will allow a 14″ or 350mm of ripping capacity to the left of the blade. Once the base assembly and fence are repositioned or remixed from the rails, three pairs of stops on the rails will guarantee the perfect alignment and calibration of the system.
INCRA table saw fence specifications:
• INCRA LS Positioning Base
• Range positioner – Right Blade: 32″ or 810 mm Metric
• Accuracy of positioning – 0.002″ over a full range
• Repeatability – Return to any former positin in just a few seconds with no repeatability error
• Fence Length: 36″
TS-LS TABLE SAW FENCE – RANGE 32″:
• TS-IIIA MOUNT – Base Mount Unit, TS-IIIA Rip Fence
• 72″ Rails (pair)
• INCRA LS 32″ Range Positioner
INCRA TABLE SAW FENCE – range 52″:
• TS-IIIA MOUNT – Base Mount Unit, IIIA Rip Fence
• 92″ Rails (pair)
• INCRA LS 32″ Range Positioner
• Rail Support Legs
Incra table saw fence installation
The TS-LS system can be used for most cast iron table saws (10″) without any tapping or drilling.
Will the INCRA fence fit on your table saw?
You need to check these two things:
1. The length of miter gauge slot:
The front to back distance of the table has to be 28-1/2” ( 724 mm ) or less. This measurement is mostly ideal for 10″ table saw.
If the distance is between 28-1/2” and 33” (724 mm – 838 mm) you can order the fence system with a longer extrusion and base support panel. This works as an alternative to the standard-length components.
2. The rear and front surfaces of the saw:
The rear and front surfaces of the saw should be flat and square to the top. They must come with two holes on each surface.
The diameter and locations of these holes are not that important. The brackets work with holes of any pattern and size.
Key features and upgrades
INCRA METRIC with an upgrade for large table
This system uses an (810 mm) LS Positioner along with two 72” rails. The XL Mount Unit can work with saws with depth in between 28″ and 33-1/2” front to back along with the miter slot.
INCRA METRIC with wonder fence
This uses an LS Positioner (810 mm) with two 72″ rails and the wonder fence. The standard unit works with saws of 28″ or less front to back along with the miter slot.
INCRA METRIC wonder fence and an upgrade for large table
This utilizes an LS Positioner (810 mm) with two 72″ rails and the wonder fence. The XL Mount can operate saws of depth in between 28″ to 33-1/2″ front to back along with the miter slot.
INCRA METRIC with wonder fence and 234 cm rails
It uses the same LS Positioner (810 mm) with two 92″ rails and wonder fence. The standard unit can work with saws with a depth of 28″ or less front to back along with the miter slot.
TS-III Support Legs
To upgrade an existing INCRA Table Saw System without legs.
Metric INCRA LS 32 – Positioner Only
This can be used with saws in concurrence with the INCRA TS rail system.
Incra Base Assembly METRIC – only for Table Saw Fence
If you need another base for your fence positioner, you can go for this.
Metric Wonder Fence Upgrade – WF/ULTRA
This upgrade is directly compatible with TS-LS fence systems.
INCRA Large-Saw Conversion Upgrade
This upgrade lets you install the fence on saws with depth of 28″ or more front to back. It comes with a 46-1/2″ CNC machined fence section and a 34″ base support panel.
TS Base Mount Package with 72″ rails and 32″ Rip Capacity
This lets you use the Positioner as a replacement rip fence. It comes with a 36″ rip fence ( computer machined ), 72″ TS rails, two locking fence glides, 723 mm positioner base support assembly, and six rail mounting brackets but no TSLS plate is not included.
TS Base Mount Package with 92″ rails and 52″ Rip Capacity
This package is the same as the one mentioned earlier but it comes with longer rails which is amazing. It includes a 36″ rip fence ( computer machined ), 723 mm positioner base support assembly, 92″ TS rails, two locking fence glides, and six rail mounting brackets. It does not come with the red TSLS plate but the TS support legs are included.
Pair rail mounting brackets with mounting hardware
If you are ever in need of more brackets that the ones that are already included in the fence, you can pair the mounting brackets with mounting hardware.
INCRA Router Table and Support Hardware Kit TSRTHW
Another great addition is that you can integrate a router unit into the INCRA table saw fence system. There’s a tailored space on the left of the fence where you can attach the router table.
Automatic positioning control
The best part of this fence is the automatic positioning control system. You will no longer have to depend on tape measures or just eyesight.
The fence is constructed with high-grade materials to fit your saw and work flawlessly for your job. Quality steel and aluminum are used in the making.
No repeatability error
You can repeat a cut or return to a previous position in just a few seconds without any repeatability error.
Too much space
The fence takes up a lot of space especially when it is fully extended. So this might be a problem if your workstation doesn’t have enough space to cater this fence’s space needs.
It costs much higher than the general fence’s available in the market.
This article shows all the good and bad sides of the incra table saw fence review. This incredible fence covers up for most of the shortcomings that the previous table saw fences had.
If you’re looking for a well fitted, manageable, and innovative fence for your table saw, you can try using this fence because we think the product is worth giving a try.